Diameters / Packaging

Diameters	44 lb Spool	900 lb Accu-Pak® Box	1000 lb Accu-Pak® Box
0.035 in (0.9 mm)	ED037831	ED037830
0.040 in (1.0 mm)	ED037829		ED037828
0.045 in (1.1 mm)	ED037698		ED037697
1.2 mm (0.047 in)	ED037556		ED037555

SuperArc® XLS

MIG (GMAW)

AWS:
ISO 14341-A : G 42 3 M20 Z

Partenaire commercial Lincoln Electric?

Connectez-vous pour voir votre prix

Acheter maintenant

Détails

Traits

Minimize surface silicates for exceptionally clean weld surface
Reduced silicates for improved paint adhesion and increased corrosion resistance
Microguard® Ultra surface treatment for consistent, stable arc performance with little to no weld spatter
Optimized for use with Rapid X® LS mode to lower silicate island formation and spatter generation

Applications typiques

Fillet and lap welds on thin material, including but not limited to automotive frames, chassis and suspension components
Designed specifically for high speed, single pass applications

Positions de soudage

Flat/Horizontal

Gaz de protection

Mixed Shielding Gas

Disclaimers

Warning -

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov

Des informations de service

BEFORE USE, READ AND UNDERSTAND THE SAFETY DATA SHEET (SDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. SDS Search page

See test result disclaimer

CONFORMANCE

CONFORMANCES	SPECIFICATION	CLASSIFICATION
ISO	ISO 14341-A	G 42 3 M20 Z

MECHANICAL PROPERTIES

Classification	Shielding Gas	Polarity	Yield Strength @ 0.2% Offset MPa (ksi)	Tensile Strength MPa (ksi)	Elongation %	Charpy V-Notch J (ft-lbs) @ -30°C (-20°F)
G 42 3 M20 Z Requirement	M20	Info. Only	420 (61) min.	500-640 (72-93)	20 min.	47 (35) min.
Typical Result, As-welded	90% Ar, 10% CO2	DC+	440 (64)	530 (77)	24	102-184 (75-136)

WIRE COMPOSITION

Classification	%Al	%C	%Cr	%Mn	%Mo	%Ni	%P	%S	%Si	%Total Cu	%V	%Ti+Zr
Typical Result	0.02	0.07	0.02	1.68	0.00 max.	0.27	0.004	0.004	0.05	0.17	0.01	0.09

TYPICAL OPERATING PROCEDURES

Diameter	Transfer Mode	Shielding Gas	Polarity	CTWD mm (in.)	Wire Feed Speed m/min (in/min)	Voltage volts	Approx. Current amps	Melt-off Rate kg/hr (lb/hr)
1.2 mm (3/64")	Spray Transfer	80% Ar, 20% CO2	DC+	19 (³/₄)	3.8 (150)	24	120	2.0 (4.5)
1.2 mm (3/64")	Spray Transfer	80% Ar, 20% CO2	DC+	19 (³/₄)	8.9 (350)	29	265	4.7 (10.3)
1.2 mm (3/64")	Spray Transfer	80% Ar, 20% CO2	DC+	19 (³/₄)	14.0 (550)	32	370	7.3 (16.2)
1.2 mm (3/64")	Spray Transfer	90% Ar, 10% CO2	DC+	19 (³/₄)	3.8 (150)	23	125	2.0 (4.5)
1.2 mm (3/64")	Spray Transfer	90% Ar, 10% CO2	DC+	19 (³/₄)	8.9 (350)	28	255	4.7 (10.4)
1.2 mm (3/64")	Spray Transfer	90% Ar, 10% CO2	DC+	19 (³/₄)	14.0 (550)	32	360	7.3 (16.0)
.040" (1.0 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	5.6 (220)	23	105	2.1 (4.6)
.040" (1.0 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	8.9 (350)	26	170	3.3 (7.3)
.040" (1.0 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	11.4 (450)	28	210	4.2 (9.3)
.040" (1.0 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	15.2 (600)	30	260	5.9 (13.1)
.040" (1.0 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	5.6 (220)	22	105	2.2 (4.8)
.040" (1.0 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	8.9 (350)	25	170	3.3 (7.3)
.040" (1.0 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	11.4 (450)	27	210	4.2 (9.3)
.040" (1.0 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	15.2 (600)	29	260	5.7 (12.6)
.035" (0.9 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	6.4 (250)	23	100	1.9 (4.1)
.035" (0.9 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	8.9 (350)	25	140	2.6 (5.8)
.035" (0.9 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	12.7 (500)	27	180	3.9 (8.5)
.035" (0.9 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	16.5 (650)	29	220	5.1 (11.3)
.035" (0.9 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	6.4 (250)	24	100	1.9 (4.2)
.035" (0.9 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	8.9 (350)	26	140	2.6 (5.8)
.035" (0.9 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	12.7 (500)	28	180	3.9 (8.5)
.035" (0.9 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	16.5 (650)	30	220	4.9 (10.9)