Menu zamknij
SuperArc XLS

Średnica / Opakowanie

Średnice
 44 lb Spool
 1000 lb Accu-Pak® Box
0.047 in (1.2 mm) ED037555
1.0 mm ED037829
1.1 mm ED037698
1.2 mm ED037556

SuperArc® XLS

Spawanie metodą MIG (GMAW)

KLASYFIKACJE:
ISO 14341-A : G 42 3 M20 Z

Średnica

Wybierz średnicę

  • 0.047 in (1.2 mm)
  • 1.0 mm
  • 1.1 mm
  • 1.2 mm

Zestaw

Wybierz pakiet

  • 44 lb Spool
  • 1000 lb Accu-Pak® Box

Wprowadzenie

Zalety

  • Minimize surface silicates for exceptionally clean weld surface
  • Reduced silicates for improved paint adhesion and increased corrosion resistance
  • Microguard® Ultra surface treatment for consistent, stable arc performance with little to no weld spatter
  • Optimized for use with Rapid X® LS mode to lower silicate island formation and spatter generation

Zastosowania standardowe

  • Fillet and lap welds on thin material, including but not limited to automotive frames, chassis and suspension components
  • Designed specifically for high speed, single pass applications

Pozycja spawania

  • Flat/Horizontal

Gaz osłonowy

  • Mixed Shielding Gas

Informacje o usługach

BEFORE USE, READ AND UNDERSTAND THE SAFETY DATA SHEET (SDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. Strona wyszukiwania kart SDS

CONFORMANCE

CONFORMANCES SPECIFICATION CLASSIFICATION
ISO ISO 14341-A G 42 3 M20 Z

MECHANICAL PROPERTIES

Classification Shielding Gas Polarity Yield Strength @ 0.2% Offset
MPa (ksi) 		Tensile Strength
MPa (ksi) 		Elongation
% 		Charpy V-Notch
J (ft-lbs) @ -30°C (-20°F)
G 42 3 M20 Z Requirement M20 Info. Only 420 (61) min. 500-640 (72-93) 20 min. 47 (35) min.
Typical Result, As-welded 90% Ar, 10% CO2 DC+ 440 (64) 530 (77) 24 102-184 (75-136)

WIRE COMPOSITION

Classification %Al %C %Cr %Mn %Mo %Ni %P %S %Si %Total Cu %V %Ti+Zr
Typical Result 0.02 0.07 0.02 1.68 0.00 max. 0.27 0.004 0.004 0.05 0.17 0.01 0.09

TYPICAL OPERATING PROCEDURES

Diameter Transfer Mode Shielding Gas Polarity CTWD
mm (in.) 		Wire Feed Speed
m/min (in/min) 		Voltage
volts 		Approx. Current
amps 		Melt-off Rate
kg/hr (lb/hr)
1.2 mm (3/64") Spray Transfer 80% Ar, 20% CO2 DC+ 19 (³/₄) 3.8 (150) 24 120 2.0 (4.5)
1.2 mm (3/64") Spray Transfer 80% Ar, 20% CO2 DC+ 19 (³/₄) 8.9 (350) 29 265 4.7 (10.3)
1.2 mm (3/64") Spray Transfer 80% Ar, 20% CO2 DC+ 19 (³/₄) 14.0 (550) 32 370 7.3 (16.2)
1.2 mm (3/64") Spray Transfer 90% Ar, 10% CO2 DC+ 19 (³/₄) 3.8 (150) 23 125 2.0 (4.5)
1.2 mm (3/64") Spray Transfer 90% Ar, 10% CO2 DC+ 19 (³/₄) 8.9 (350) 28 255 4.7 (10.4)
1.2 mm (3/64") Spray Transfer 90% Ar, 10% CO2 DC+ 19 (³/₄) 14.0 (550) 32 360 7.3 (16.0)
.040" (1.0 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 5.6 (220) 23 105 2.1 (4.6)
.040" (1.0 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 8.9 (350) 26 170 3.3 (7.3)
.040" (1.0 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 11.4 (450) 28 210 4.2 (9.3)
.040" (1.0 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 15.2 (600) 30 260 5.9 (13.1)
.040" (1.0 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 5.6 (220) 22 105 2.2 (4.8)
.040" (1.0 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 8.9 (350) 25 170 3.3 (7.3)
.040" (1.0 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 11.4 (450) 27 210 4.2 (9.3)
.040" (1.0 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 15.2 (600) 29 260 5.7 (12.6)
.035" (0.9 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 6.4 (250) 23 100 1.9 (4.1)
.035" (0.9 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 8.9 (350) 25 140 2.6 (5.8)
.035" (0.9 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 12.7 (500) 27 180 3.9 (8.5)
.035" (0.9 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 16.5 (650) 29 220 5.1 (11.3)
.035" (0.9 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 6.4 (250) 24 100 1.9 (4.2)
.035" (0.9 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 8.9 (350) 26 140 2.6 (5.8)
.035" (0.9 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 12.7 (500) 28 180 3.9 (8.5)
.035" (0.9 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 16.5 (650) 30 220 4.9 (10.9)