Menü Schließen
Hardfacing Consumables Family Group

Durchmesser / Lieferform

Durchmesser
 11.3 KG SPOOL
 22.7 KG COIL
1,1 mm ED031131
1,6 mm ED031132
2,0 mm ED019887

Lincore® 60-O

Schweißen mit selbstschützenden Fülldrähten (FCAW-S)

LINCORE® 60-O Wire designed for bucket lips, crusher hammers, dozer blades, and ripper teeth applications.

Durchmesser

Durchmesser wählen

  • 1,1 mm
  • 1,6 mm
  • 2,0 mm

Lieferform

Lieferform auswählen

  • 11.3 KG SPOOL
  • 22.7 KG COIL

DETAILS

LINCORE® 60-O ideal for carbon, low alloy, manganese, stainless steels and cast iron to be used at temperatures up to 704°C (1300°F) deposits feature higher alloy levels than to resist both abrasion and moderate impact limited to two layers with a Rockwell Hardness range of 55-60 (RHC) during sever abrasion.

Eigenschaften

  • Für unlegierte und niedriglegierte Stähle, Manganstahl und korrosionsbeständige Stähle
  • Schweißgut begrenzt auf zwei Lagen.
  • Schweißgut mit höherem Legierungsanteil für Beständigkeit gegen Abrieb und mäßigen Stoßverschleiß.
  • Deposit is limited to two layers

Typische Anwendungen

  • Schaufelkanten
  • Brecherhämmer
  • Erzrutschen
  • Planierer
  • Grubberzähne

Schweißpositionen

  • Flach/Horizontal

Service Informationen

Dokumentation

Ergänzende Produkte

33 lb Steel Spool Outershield MC-409 Flux-Cored Wire

Lincore® 60-O

ED031132
50lb Coil Ultracore 70C

Lincore® 60-O

ED019887

BEFORE USE, READ AND UNDERSTAND THE SAFETY DATA SHEET (SDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. SDS-Suchseite

MECHANICAL PROPERTIES

Classification Number of layer Hardness Rockwell C Mass Loss (G65)
Typical Result 1 Layer 50-55 0.67
Typical Result 2 Layers 55-58 0.20

DEPOSIT COMPOSITION

Classification Number of layer %Al %C %Cr %Mn %Si
Typical Result 2 Layers 0.3-0.4 4.0-4.6 18.5-22.9 1.0-1.8 0.5-0.9

TYPICAL OPERATING PROCEDURES

Diameter Polarity ESO
mm (in.) 		Wire Feed Speed
m/min (in/min) 		Voltage
volts 		Approx. Current
amps 		Deposition Rate
kg/hr (lb/hr)
.045" (1.1 mm) DC+ 19 (1) 5.1 (200) 21 125 1.9 (4.1)
.045" (1.1 mm) DC+ 19 (1) 10.2 (400) 25 185 3.7 (8.2)
.045" (1.1 mm) DC+ 19 (1) 12.7 (500) 27 210 4.7 (10.3)
1/16" (1.6 mm) DC+ 22 (1) 5.1 (200) 28 240 3.4 (7.6)
1/16" (1.6 mm) DC+ 22 (1) 7.6 (300) 31 300 5.1 (11.2)
1/16" (1.6 mm) DC+ 22 (1) 11.4 (450) 33 350 7.5 (16.6)
5/64" (2.0 mm) DC+ 32 (1) 3.2 (125) 26 250 3.4 (7.4)
5/64" (2.0 mm) DC+ 32 (1) 5.1 (200) 30 350 5.4 (12.0)
5/64" (2.0 mm) DC+ 32 (1) 6.4 (250) 32 400 6.8 (15.1)
7/64" (2.8 mm) DC+ 29 (1) 1.9 (75) 27 250 3.4 (7.4)
7/64" (2.8 mm) DC+ 29 (1) 3.2 (125) 30 340 5.4 (11.9)
7/64" (2.8 mm) DC+ 29 (1) 4.4 (175) 32 420 7.5 (16.5)

NOTES

Note
Deposit thickness limit is two layers unless high travel speed is used to obtain very closely spaced check cracks. Many layers can be used with high travel speed and small bead sizes to ensure close-spaced check cracks.
Lincore® 60-O deposit cross cracks (commonly called cross-checking) on cooling. This is desirable, since cross-cracking of the deposit relieves cooling stresses and prevents spalling.