Menu Close
SuperArc MIG wire, Steel Spool

Diameters / Packaging

Diameters
 33 lb Spool
 44 lb Spool
 60 lb Spool
 500 lb Accu-Pak® Box
 500 lb Accu-Trak® Drum
 1000 lb Accu-Pak® Box
 1000 lb Accu-Trak® Drum
 1000 lb Infinity-Pak
0.035 in (0.9 mm) ED031413 ED029546,EDS30775 EDS01372 EDS29590
0.045 in (1.1 mm) ED031414 EDS30776 EDS01380 ED032919 ED001378 ED034436 ED029591
0.052 in (1.3 mm) EDS30777 ED032920 ED026627 EDS29592 ED034955
1/16 in (1.6 mm) ED037362

SuperArc® LA-90™

MIG (GMAW) | ED031413

AWS:
ER90S-D2
ER80S-D2

Le SuperArc® LA-90™ de Lincoln Electric est un fil MIG faiblement allié revêtu de cuivre de qualité supérieure, fabriqué pour répondre aux exigences de résistance à la traction de 80 000 à 90 000 psi (552 à 620 MPa) minimum.

Diamètre

Sélectionnez le diamètre

  • 0.035 in (0.9 mm)
  • 0.045 in (1.1 mm)
  • 0.052 in (1.3 mm)
  • 1/16 in (1.6 mm)

Paquet

Sélectionnez un forfait

  • 33 lb Spool
  • 44 lb Spool
  • 500 lb Accu-Trak® Drum
  • 1000 lb Accu-Trak® Drum
Acheter maintenant

Détails

Notre fil MIG faiblement allié revêtu de cuivre de qualité supérieure est fabriqué pour répondre aux exigences de résistance à la traction de 80 000 à 90 000 psi (552 à 620 MPa) minimum.

Traits

  • Capable de produire des dépôts de soudure avec une résistance à la traction de 550 à 620 MPa (80 à 90 ksi)
  • Contient 0,50% de molybdène pour la résistance après la détente
  • Microguard® Ultra offre une alimentation et une stabilité de l'arc supérieures
  • Prend en charge le transfert par court-circuit, le transfert globulaire, le transfert par pulvérisation axiale et le transfert par pulvérisation pulsée

Disclaimers

Warning -

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov

Des informations de service

Vous pourriez également avoir besoin

Image not found

Magnum® Contact Tip - Standard, .035 in (0.9 mm) - 10/pack

KP14-35
Drive Roll and Guide Tube Kit

Drive roll kit (2R) 0.9 mm

KP1696-035S
Magnum Gun Liner

Cable Liner .035-.045 in (0.9-1.2 mm) 15 ft (4.6 m)

KP42-4045-15
Gas Diffuser

Gas Diffuser

KP52FN
Voir tout

BEFORE USE, READ AND UNDERSTAND THE SAFETY DATA SHEET (SDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. SDS Search page

See test result disclaimer

CONFORMANCE

CONFORMANCES SPECIFICATION CLASSIFICATION
AWS AWS A5.28 ER80S-D2, ER90S-D2
CWB CWB AWS A5.28 ER55S-D2 (ER80S-D2), ER62S-D2 (ER90S-D2)
MIL MIL-E-23765/2E MIL-80S-3

MECHANICAL PROPERTIES

Classification Shielding Gas Polarity Yield Strength @ 0.2% Offset
MPa (ksi) 		Tensile Strength
MPa (ksi) 		Elongation
% 		Charpy V-Notch
J (ft-lbs) @ -30°C (-20°F)
ER80S-D2 Requirement 100% CO2 DC+ 470 (68) min. 550 (80) min. 17 min. 27 (20) min.
ER90S-D2 Requirement 1-5% O2, balance Ar DC+ 540 (78) min. 620 (90) min. 17 min. 27 (20) min.
Typical Result, As-welded 100% CO2 DC+ 510 (74) 610-670 (88-96) 17 27-103 (20-76)
Typical Result, As-welded 95% Ar, 5% O2 DC+ 540 (79) 640-670 (93-97) 24 74-205 (55-151)
Typical Result, As-welded 98% Ar, 2% O2 DC+ 610 (88) 680-740 (99-107) 23 96-183 (71-135)

WIRE COMPOSITION

Classification %C %Cr %Mn %Mo %Ni %P %S %Si %Total Cu
ER90S-D2 Requirement 0.07 - 0.12 1.60 - 2.10 0.40 - 0.60 0.15 max. 0.025 max. 0.025 max. 0.50 - 0.80 0.50 max.
Typical Result 0.07-0.10 0.02 1.69-1.87 0.44-0.51 0.01-0.02 0.006-0.009 0.004-0.011 0.57-0.70 0.14-0.23

TYPICAL OPERATING PROCEDURES

Diameter Transfer Mode Shielding Gas Polarity CTWD
mm (in.)⁽¹⁾ 		Wire Feed Speed
m/min (in/min) 		Voltage
volts 		Approx. Current
amps 		Melt-off Rate
kg/hr (lb/hr)
0.035 in (0.9 mm) Short Circuit Transfer ⁽²⁾ 75% Ar / 25% CO2 DC+ 9-12 (3/8-1/2) 2.5 (100) 18 80 0.7 (1.6)
0.035 in (0.9 mm) Short Circuit Transfer ⁽²⁾ 75% Ar / 25% CO2 DC+ 9-12 (3/8-1/2) 3.8 (150) 19 120 1.1 (2.4)
0.035 in (0.9 mm) Short Circuit Transfer ⁽²⁾ 75% Ar / 25% CO2 DC+ 9-12 (3/8-1/2) 6.4 (250) 22 175 1.8 (4.0)
0.035 in (0.9 mm) Spray Transfer 90% Ar / 10% CO2 DC+ 12-19 (1/2-3/4) 9.5 (375) 23 195 2.7 (6.0)
0.035 in (0.9 mm) Spray Transfer 90% Ar / 10% CO2 DC+ 12-19 (1/2-3/4) 12.7 (500) 29 230 3.6 (8.0)
0.035 in (0.9 mm) Spray Transfer 90% Ar / 10% CO2 DC+ 12-19 (1/2-3/4) 15.2 (600) 30 275 4.4 (9.6)
0.045 in (1.1 mm) Short Circuit Transfer ⁽²⁾ 75% Ar / 25% CO2 DC+ 12-19 (1/2-3/4) 3.2 (125) 19 145 1.5 (3.4)
0.045 in (1.1 mm) Short Circuit Transfer ⁽²⁾ 75% Ar / 25% CO2 DC+ 12-19 (1/2-3/4) 3.8 (150) 20 165 1.8 (4.0)
0.045 in (1.1 mm) Short Circuit Transfer ⁽²⁾ 75% Ar / 25% CO2 DC+ 12-19 (1/2-3/4) 5.1 (200) 21 200 2.5 (5.4)
0.045 in (1.1 mm) Spray Transfer 90% Ar / 10% CO2 DC+ 12-19 (1/2-3/4) 8.9 (350) 27 285 4.2 (9.2)
0.045 in (1.1 mm) Spray Transfer 90% Ar / 10% CO2 DC+ 12-19 (1/2-3/4) 12.1 (475) 30 335 5.7 (12.5)
0.045 in (1.1 mm) Spray Transfer 90% Ar / 10% CO2 DC+ 12-19 (1/2-3/4) 12.7 (500) 30 340 6.0 (13.2)
0.052 in (1.3 mm) Spray Transfer 90% Ar / 10% CO2 DC+ 12-19 (1/2-3/4) 7.6 (300) 30 300 4.8 (10.6)
0.052 in (1.3 mm) Spray Transfer 90% Ar / 10% CO2 DC+ 12-19 (1/2-3/4) 8.1 (320) 30 320 5.2 (11.5)
0.052 in (1.3 mm) Spray Transfer 90% Ar / 10% CO2 DC+ 12-19 (1/2-3/4) 12.3 (485) 32 430 7.8 (17.1)
1/16 in (1.6 mm) Spray Transfer 90% Ar / 10% CO2 DC+ 12-25 (1/2-1) 5.3 (210) 25 325 4.8 (10.7)
1/16 in (1.6 mm) Spray Transfer 90% Ar / 10% CO2 DC+ 12-25 (1/2-1) 6.0 (235) 27 350 5.4 (12.0)
1/16 in (1.6 mm) Spray Transfer 90% Ar / 10% CO2 DC+ 12-25 (1/2-1) 7.4 (290) 28 430 6.7 (14.8)

NOTES

Note
⁽¹⁾ CTWD (Contact Tip to Work Distance). Subtract 1/4 in (6.4 mm) to calculate Electrical Stickout.
⁽²⁾ Procedures in these areas are procedures for short circuiting mode using 75% Argon, 25% CO2. NOTE: For 100% CO2 procedures, add 1 to 2 volts for short circuit transfer and 2 to 3 volts for globular transfer.