Innershield, Outershield, 10 lb. or 12.5 lb plastic spool

Diameters / Packaging

Diameters
10 lb Spool
25 lb Spool
33 lb Spool
50 lb Coil
500 lb Accu-Trak® Drum
600 lb Speed Feed® Reel
0.035 in (0.9 mm) ED026804 ED026805
0.045 in (1.1 mm) ED020836 ED022659 ED030007 ED020844 ED027364
0.052 in (1.3 mm) ED022660 ED030008 ED020845 ED029778
1/16 in (1.6 mm) ED022661 ED030009 ED020846 ED029779 ED020851

Outershield® 71M Flux-cored (FCAW-G) Wire

Flux-Cored Gas-Shielded (FCAW-G) | ED020836

AWS:
E71T-9C-J
E71T-9M-J
E71T1-C1A4-CS1-H16
E71T1-M21A4-CS1-H16

Outershield® 71M from Lincoln Electric is an overall performer - from excellent feedability to good arc performance.

Détails

An overall performer – from excellent feedability to good arc performance. No side cutters are required to restart, just break the wire off in your hands – it's that easy.

Traits

  • Dual classified for both 100% CO2 and 75% Argon / 25% CO2 mixed gas
  • Charpy V-Notch impact toughness tested to -40°C (-40°F)
  • High travel speeds
  • Spray like transfer with minimal spatter
  • Rod based manufacturing for industry leading wire stiffness and feedability
  • Increased rigidity allows for easy manual break-off

Disclaimers

Warning -

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov

Vous pourriez également avoir besoin

BEFORE USE, READ AND UNDERSTAND THE SAFETY DATA SHEET (SDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. SDS Search page

See test result disclaimer

CONFORMANCE

CONFORMANCES SPECIFICATION CLASSIFICATION
AWS AWS A5.20 E71T-1C-J, E71T-1C-JH16, E71T-1M-J, E71T-1M-JH16, E71T-9C-J, E71T-9C-JH16, E71T-9M-J, E71T-9M-JH16
AWS AWS A5.36 E71T1-C1A4-CS1-H16, E71T1-M21A4-CS1-H16
ABS ABS - Part 2 3YSA, 3YSA H15
BV BV - Chapter 5 SA3YH
CWB CSA W48 E491T1-C1A4-CS1-H16, E491T1-M21A4-CS1-H16, E491T-9J-H16, E491T-9MJ-H16
DNV-GL DNV - 2.9 III YMS H10
LR LR - Chapter 11 3YS H15
MIL MIL-E-24403/1D MIL-71T-1C, MIL-71T-1M

MECHANICAL PROPERTIES

Classification Shielding Gas Polarity Yield Strength @ 0.2% Offset
MPa (ksi)
Tensile Strength
MPa (ksi)
Elongation
%
Charpy V-Notch
J (ft-lbs) @ -20°C (0°F)
Charpy V-Notch
J (ft-lbs) @ -30°C (-20°F)
Charpy V-Notch
J (ft-lbs) @ -40°C (-40°F)
E71T-9C-JH16 Requirement 100% CO2 DC+ 400 (58) min. 480-660 (70-95) 22 min. 27 (20) min.
E71T-9M-JH16 Requirement 75-80% Ar, balance CO2 DC+ 400 (58) min. 480-660 (70-95) 22 min. 27 (20) min.
E71T1-C1A4-CS1-H16 Requirement 100% CO2 DC+ 400 (58) min. 480-660 (70-95) 22 min. 27 (20) min.
E71T1-M21A4-CS1-H16 Requirement M21-ArC DC+ 400 (58) min. 480-660 (70-95) 22 min. 27 (20) min.
Typical Result, As-welded 100% CO2 DC+ 470 (68) 540-600 (78-87) 26 176-224 (130-165) 167-184 (123-136) 68-174 (50-128)
Typical Result, As-welded 75% Ar, 25% CO2 DC+ 540 (78) 630-650 (91-94) 23 148-155 (109-114) 133-142 (98-105) 103-148 (76-109)

DEPOSIT COMPOSITION

Classification Shielding Gas Polarity %B %C %Mn %P %S %Si Diffusible Hydrogen
mL/100g Weld Metal
E71T-9C-JH16 Requirement 100% CO2 DC+ 0.12 max. 1.75 max. 0.03 max. 0.03 max. 0.90 max. 16.0 max.
E71T-9M-JH16 Requirement 75-80% Ar, balance CO2 DC+ 0.12 max. 1.75 max. 0.03 max. 0.03 max. 0.90 max. 16.0 max.
E71T1-C1A4-CS1-H16 Requirement 100% CO2 DC+ 0.12 max. 1.75 max. 0.030 max. 0.030 max. 0.90 max. 16 max.
E71T1-M21A4-CS1-H16 Requirement M21-ArC DC+ 0.12 max. 1.75 max. 0.030 max. 0.030 max. 0.90 max. 16 max.
Typical Result 100% CO2 DC+ 0.0039-0.0053 0.05-0.07 1.15-1.36 0.014 max. 0.014 max. 0.31-0.41
Typical Result 75% Ar, 25% CO2 DC+ 0.0049-0.0059 0.06-0.08 1.43-1.61 0.014 max. 0.014 max. 0.46-0.53 9.8

TYPICAL OPERATING PROCEDURES

Diameter Shielding Gas⁽¹⁾ Polarity CTWD
mm (in.)⁽²⁾
Wire Feed Speed
m/min (in/min)
Voltage
volts
Approx. Current
amps
Melt-off Rate
kg/hr (lb/hr)
Deposition Rate
kg/hr (lb/hr)
Efficiency
%
0.035 in (0.9 mm) 100% CO2 DC+ 19-25 (3/4-1) 5.1 (200) 20-23 95 1.3 (2.8) 1.1 (2.8) 85
0.035 in (0.9 mm) 100% CO2 DC+ 19-25 (3/4-1) 6.4 (250) 21-24 115 1.6 (3.5) 1.4 (3.5) 85
0.035 in (0.9 mm) 100% CO2 DC+ 19-25 (3/4-1) 7.6 (300) 22-25 130 1.9 (4.2) 1.6 (4.2) 86
0.035 in (0.9 mm) 100% CO2 DC+ 19-25 (3/4-1) 8.9 (350) 23-26 150 2.2 (4.9) 1.9 (4.9) 86
0.035 in (0.9 mm) 100% CO2 DC+ 19-25 (3/4-1) 10.2 (400) 24-27 160 2.6 (5.6) 2.2 (5.6) 86
0.035 in (0.9 mm) 100% CO2 DC+ 19-25 (3/4-1) 12.7 (500) 26-29 185 3.2 (7.0) 2.7 (7.0) 86
0.035 in (0.9 mm) 100% CO2 DC+ 19-25 (3/4-1) 15.2 (600) 28-31 200 3.8 (8.4) 3.3 (8.4) 86
0.035 in (0.9 mm) 100% CO2 DC+ 19-25 (3/4-1) 17.8 (700) 30-33 215 4.4 (9.8) 3.8 (9.8) 86
0.045 in (1.1 mm) 100% CO2 DC+ 19-25 (3/4-1) 5.1 (200) 23-26 165 2.1 (4.6) 1.8 (3.9) 83
0.045 in (1.1 mm) 100% CO2 DC+ 19-25 (3/4-1) 6.4 (250) 24-27 190 2.6 (5.8) 2.2 (4.8) 84
0.045 in (1.1 mm) 100% CO2 DC+ 19-25 (3/4-1) 7.6 (300) 25-28 220 3.1 (6.9) 2.6 (5.8) 84
0.045 in (1.1 mm) 100% CO2 DC+ 19-25 (3/4-1) 8.9 (350) 26-29 245 3.7 (8.1) 3.1 (6.8) 84
0.045 in (1.1 mm) 100% CO2 DC+ 19-25 (3/4-1) 10.2 (400) 26-29 265 4.2 (9.2) 3.5 (7.8) 84
0.045 in (1.1 mm) 100% CO2 DC+ 19-25 (3/4-1) 12.7 (500) 28-31 295 5.2 (11.5) 4.4 (9.7) 84
0.045 in (1.1 mm) 100% CO2 DC+ 19-25 (3/4-1) 15.2 (600) 30-33 315 6.3 (13.8) 5.3 (11.7) 85
0.045 in (1.1 mm) 100% CO2 DC+ 19-25 (3/4-1) 17.8 (700) 32-35 325 7.3 (16.1) 6.2 (13.7) 85
0.052 in (1.3 mm) 100% CO2 DC+ 19-25 (3/4-1) 3.8 (150) 22-25 150 2.1 (4.7) 1.7 (3.8) 81
0.052 in (1.3 mm) 100% CO2 DC+ 19-25 (3/4-1) 5.1 (200) 23-26 180 2.8 (6.2) 2.3 (5.1) 83
0.052 in (1.3 mm) 100% CO2 DC+ 19-25 (3/4-1) 6.4 (250) 24-27 210 3.5 (7.7) 2.9 (6.5) 83
0.052 in (1.3 mm) 100% CO2 DC+ 19-25 (3/4-1) 7.6 (300) 25-28 235 4.2 (9.3) 3.5 (7.8) 84
0.052 in (1.3 mm) 100% CO2 DC+ 19-25 (3/4-1) 8.9 (350) 27-30 265 4.9 (10.8) 4.2 (9.1) 84
0.052 in (1.3 mm) 100% CO2 DC+ 19-25 (3/4-1) 11.4 (450) 29-32 305 6.3 (13.9) 5.4 (11.8) 85
0.052 in (1.3 mm) 100% CO2 DC+ 19-25 (3/4-1) 12.7 (500) 30-33 325 7.0 (15.5) 6.0 (13.2) 85
0.052 in (1.3 mm) 100% CO2 DC+ 19-25 (3/4-1) 15.2 (600) 33-36 360 8.4 (18.6) 7.2 (15.8) 85
1/16 in (1.6 mm) 100% CO2 DC+ 19 (3/4) 3.2 (125) 23-26 205 2.5 (5.4) 2.0 (4.5) 82
1/16 in (1.6 mm) 100% CO2 DC+ 19 (3/4) 3.8 (150) 24-27 225 3.0 (6.5) 2.4 (5.4) 82
1/16 in (1.6 mm) 100% CO2 DC+ 19 (3/4) 5.1 (200) 25-28 260 4.0 (8.7) 3.3 (7.2) 83
1/16 in (1.6 mm) 100% CO2 DC+ 19 (3/4) 6.4 (250) 26-29 295 4.9 (10.9) 4.1 (9.1) 83
1/16 in (1.6 mm) 100% CO2 DC+ 19 (3/4) 7.6 (300) 28-31 330 5.9 (13.0) 5.0 (10.9) 84
1/16 in (1.6 mm) 100% CO2 DC+ 25 (1) 10.2 (400) 30-33 395 7.9 (17.4) 6.6 (14.6) 84
1/16 in (1.6 mm) 100% CO2 DC+ 25 (1) 12.7 (500) 33-36 445 9.9 (21.7) 8.3 (18.3) 84

NOTES

Note
⁽¹⁾ When welding under mixed gas, decrease voltage.
⁽²⁾ To estimate ESO, subtract 1/4 in. (6.0 mm) from CTWD.